Before you buy a new computer for drone mapping, it helps to know what the machine actually does during processing. Photogrammetry computer requirements are not a single number. They depend on how many photos you process, how large those photos are, which settings you choose, and above all which software you run. This guide walks through how RAM, the GPU and storage each affect a processing job, and how to read a vendor's requirements page so you buy for your real projects rather than for a forum build.
If you are new to the software side, start with what photogrammetry software does. This post assumes you already know photos go in and maps come out, and focuses on the hardware in the middle.
Why photogrammetry computer requirements vary by software
Every processing package is built differently. One may lean heavily on the CPU, another may push more work to the graphics card, and each one publishes its own minimum and recommended specs. Two vendors' documentation, both checked on 17 Nov 2026, show how much the guidance differs:
- Pix4D's PIX4Dmapper computer requirements page sizes RAM and free disk space by project size, measured in images at 14 MP. It lists a recommended 16 GB RAM and 30 GB of SSD free space for medium projects of 100 to 500 images, and 32 GB RAM and 60 GB of SSD free space for large projects of 500 to 1,000 images.
- Agisoft's Metashape system requirements page describes a Basic Configuration with 16 to 32 GB RAM and an Advanced Configuration with 32 to 128 GB RAM, and its hardware recommendations article lists a recommended configuration with a discrete NVIDIA or AMD GPU (4+ GB VRAM) and 32 GB of RAM.
Those figures belong to those products. They are useful for showing how vendors think about sizing, but they are not a spec for any other program. The practical rule is simple: plan your computer around the published requirements of the software you will actually use, and treat everything else as background reading.
RAM: the limit on how big a job can be
RAM is usually the first thing that stops a large job. Photogrammetry software holds image data, matched features and intermediate surfaces in memory while it works, so the number of photos and their resolution drive how much RAM a project needs.
Both vendor pages above tie RAM to project size rather than to a fixed figure. Pix4D's table steps up with image count, and Agisoft's hardware article says it usually recommends 32 GB or 64 GB RAM for desktop systems when a task needs high reconstruction quality or a large number of images. When you plan RAM, think about:
- Your typical photo count. A small roof job and a 200-acre site are different workloads.
- Your camera's resolution. Higher-megapixel sensors produce more data per photo.
- Your largest regular job, not your average. Size for the projects you take on often, and know whether the motherboard has open slots for an upgrade later.
If a job runs out of memory, the usual workarounds are splitting the project into smaller blocks or lowering processing settings. Both cost time, which is why RAM tends to be the most important line on the spec sheet.
GPU: speed for the steps that use it
A graphics card can speed up parts of processing, but how much depends on the software. Some programs accelerate image matching and surface building on the GPU; others do most of their work on the CPU and treat the GPU as a helper. Pix4D's page lists a minimum of a GPU compatible with OpenGL 3.2, with a GeForce GTX GPU and 2 GB RAM in its recommended column. Agisoft's recommendation names a discrete GPU with 4+ GB VRAM.
Before paying for a high-end card, check three things in your software's documentation:
- Which processing steps actually use the GPU.
- Which GPU brands and driver frameworks are supported.
- Whether the vendor recommends a minimum amount of video memory.
A strong GPU paired with too little RAM will still stall on a big job. Balance matters more than any single part.
Storage: space and speed
Photogrammetry writes a lot of temporary data. A project folder can grow well beyond the size of the original photos while processing runs, then shrink once intermediate files are cleaned up. Pix4D's requirements page lists free disk space for each project size and recommends an SSD, and Agisoft's hardware article advises storing project files, including source images, on an SSD.
A workable storage plan usually looks like this:
- A fast SSD for active projects while they process.
- Enough free space on that drive for your largest regular job, with room to spare.
- Separate, larger storage for finished projects and raw photo archives, plus a backup copy.
Don't treat one build as a universal spec
Forum threads and video reviews often post a single build as "the" drone mapping PC. That build may work well for the person who posted it, with their camera, their site sizes and their software. It may be overkill for a roof inspector and underpowered for someone mapping large construction sites every week. No single build is enough for every site, and no benchmark from another program tells you how a different program will perform.
A better approach is to write down your typical job (photo count, camera resolution, deliverables), read your software's published requirements, and size RAM first, then storage, then the GPU. If you already own a capable desktop, test a real project on it before buying anything.
Where SkyView fits
Hardware matters more once processing runs on your own machine instead of in a vendor's cloud. That is the trade we chose for SkyView: SkyView Desktop turns RGB drone photos into orthomosaics on a Windows computer with no per-map processing fee, then delivers results to clients through PilotLedger. The case for that model, and what changes when the computer is yours, is covered in processing drone maps on your own hardware and desktop photogrammetry with no per-map fee.
Once the maps are done, the same PilotLedger account handles the business side of the job, including quotes, invoices and client delivery, so the work does not end in a folder on your desktop.
If you want to process on your own computer and keep the job and the client in one place, see the Pilot Ledger plans.